Showing results: 2371 - 2385 of 2756 items found.
-
FID Series -
Axiomtek Co., Ltd.
Axiomtek's FID (Flash in Disk-ATA) series is a high performance 2.5 flash disk and fully compatible with IDE standard which make it an ideal replacement for conventional IDE HDD without any driver or system modification. This 2.5 IDE flash disk is provided with huge capacities up to 256GB to meet diverse needs of data storage. With the features of high capacity storage, data integrity, anti-vibration and low power consumption, the FID series is surely a solid solution for expanding an industrial computers memory.
-
EIM-01 -
Compact Power Company
The EIM-01 external input module is used to safely isolate and input an external drive signal into the MAC-01, -02 or -03 AC Power Sources/Frequency Converters. The unit can accept various waveforms from laboratory or programmable oscillators or from a Titan MOS-01, -01A, -01B when used as a slave unit in multi-KVA systems. BNC input is completely isolated and floating with 1,500VAC breakdown and excellent common mode rejection. A recessed 8% gain adjustment control is also provided. The EIM-01 must be factory installed.
-
4-20mA -
Riverhawk Company
Loop-Powered Transmitters convert the output from proximity probes, seismic sensors, into a 4-20mA DC current, which is proportional to the input being measured. The transmitter converts the displacement or vibration signal to DC voltage and/or current for a DCS or PLC system. They control a 4-20mA current loop for a specified vibration range (ex. 0-5 mils peak-to-peak). The transmitters have a two-wire hook-up, powered solely by the loop current and have a power supply range of 15 to 36 volts.
-
TS8997 -
Rohde & Schwarz GmbH & Co. KG
The R&S®OSP-B157W8 PLUS 7.5 GHz module with up to eight channels is the core of the system and uses a printed RF switch board in solid-state relay (SSR) architecture. It allows flexible operation of the connected DUT (up to eight ports) for power measurements, signal conditioning via the integrated attenuators, couplers and combiners, RF switching to the measuring instruments in combination with the R&S®OSP-B157WX up to 40 GHz and is controlled by R&S®WMS32 software.
-
Ducommun Inc
Ducommun millimeter wave products include ACH, ARH and ALC series circular, rectangular gain horn antennas and lens corrected horn antennas for system applications. Low side lobes, ridged configuration and low cost are the main features of these antennas. The standard gain value and half power beamwidth at mid-frequency point of each waveguide band are 23 dBi and 9 degrees, respectively. Other gain values are available as customer order. These antennas cover the frequency range of 18 to 110 GHz.
-
iWave Systems Technologies
The M.2 module is based on Artix-7 FPGA that provides bridging features between PCIe and SD3.0 units to validate different memory densities of micro-SD card. For host processor communication, the module is designed with 2-Lane PCIe Gen 2.0 interfaces. The module presents compact design, flexibility, and consumes low power. Since PCIe is backward compatible with the earlier version the user can integrate into existing systems with ease. The interface towards the SD card is realized by the SD protocol implemented in the FPGA.
-
Cole-Parmer Instrument
We offer a broad range of test and measurement devices for your scientific, educational, industrial, and process applications. We carry the test and measurements tools you need to analyze, validate, and verify measurements in your electronic and mechanical systems, ensuring compliance to quality assurance and quality control programs. Our selection features portable and bench oscilloscopes, multimeters (DMMs), clamp meters, megohmmeters, stroboscopes and tachometers, power transformers, along with precision meters for humidity, moisture, light, airflow, weather, and vibration.
-
Megger Group Ltd.
Diagnostic insulation testing today represents over a hundred years of constant development. When Sydney Evershed pioneered the first insulation tests in the late 19th century, the only measurable values were insulation at 500 volts and a basic continuity check. However, measurement techniques have continuously evolved to keep pace with new insulation technologies. From electronic design and household wiring to generators and power transmission systems, all different kinds of insulation must operate at a safe minimum value.
-
780879-01 -
NI
The sbRIO‑9871 adds RS485/RS422 serial ports to CompactRIO systems. The serial ports are accessed directly from the FPGA to offer you flexibility in communicating with serial devices. The module has individual buffers on every port that save FPGA space and simplify programming. The sbRIO‑9870 supports standard start bit, stop bit, and handshaking settings. It uses an external power to provide maximum compatibility and reliability under all serial port conditions. Non-enclosed modules are designed for OEM applications.
-
780922-01 -
NI
The sbRIO‑9870 adds RS232 serial ports to CompactRIO systems. The serial ports are accessed directly from the FPGA to offer you flexibility in communicating with serial devices. The module has individual buffers on every port that save FPGA space and simplify programming. The sbRIO‑9870 supports standard start bit, stop bit, and handshaking settings. It uses an external power to provide maximum compatibility and reliability under all serial port conditions. Non-enclosed modules are designed for OEM applications.
-
778572-67 -
NI
64-Channel PXI Relay Driver Module—The PXI‑2567 is an external relay driver that works with internal or external power sources. The PXI‑2567 allows you to control relays when the current and voltage requirements for those relays exceed the capabilities found in existing relay modules or for relays embedded in a test system. The PXI‑2567 includes overcurrent, overvoltage, and flyback protection to ensure long-life operation. The PXI‑2567 can also drive small DC motors or other inductive relay coils.
-
Megger Group Ltd.
Baker's dynamic motor test and monitoring instruments are built to conduct condition monitoring tests of motors and generators from a Motor Control Centre (MCC), or through a Baker EP1000 connection unit. The Baker EXP4000 dynamic motor analyser is a low-voltage, AC- and battery-operated instrument that test motors and generators while they are in operation. The EXP4000 provides health and performance data on the motor, the motor's load, and incoming power to assess motor performance and suitability in context of the entire machine system it supports.
-
eBOX638-842-FL -
Axiomtek Co., Ltd.
The eBOX638-842-FL is powered by the quad-core Intel® Celeron® J1900 processor 2.0 GHz onboard. The rugged embedded system is equipped with a DDR3L -1066/1333 SO-DIMM slot for up to 8GB system memory. It is specially designed to offer great expandability with one I/O module slot and two PCI/PCIe expansion slots. The integrated Intel® HD Graphics engine also advances the graphics performance for this dual-view supported system. The eBOX638-842-FL is feature-rich and highly expandable and customizable. It has a customizable I/O module slot for additional LAN ports, COM ports, USB ports, or any kinds of I/O connectors depending on user requirements. Furthermore, two PCI slots can support a variety of applications such as motion and vision control. In addition, it is designed to withstand a wide operating temperature range from -10°C to +55°C and has a wide power input of 9VDC to 36VDC to operate in factory environments or any kinds of automation applications.
-
Teledyne OEM Solutions
Streamline your manufacturing process and reduce the number of suppliers you work with to focus on your core business. Teledyne OEM Solutions can assemble tubing, parts, and other small components into end-user kits, allowing you to focus on larger items. With over 50 years of experience creating kits for system setup, preventative maintenance, and consumable parts, our ready-to-go kits will save you time and money while reducing inventory and hassle.Teledyne's extensive purchasing power allows us to source high-quality parts at competitive prices, providing the best value for you and your customers. By providing these kits to your customers, you can enhance their experience and ensure their systems run smoothly and efficiently. They will appreciate the convenience and simplicity, and will thank you for it.
-
JB-(C/D) -
Jinan Testing Equipment IE Corporation
KB- (C/D) common type metallic pendulum impact testing system is the basic model for impact tester. The metallic pendulum impact tester is used to determine the impact resistance of metal materials under dynamic load and capable of doing a large number of impact tests continuously. The display method for the models is different, respectively there are analog dial display, touch screen digital display and computer display. For the later two models, it can display the impact power, impact toughness, and pendulum rotation angle. All the testing reports can be printed out. The metallic pendulum impact testing system is the essential quality control equipment for metal material manufacturers and QC departments, as well as the necessary instrument of research institutes for new material research.
